Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 5 - Jul 10
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Metal-Fab Corr/Guard 6" to 14" Aluminum Eccentric IncreaserCorr Guard is tested and listed to UL 1738 for positive pressures up to 15" w. g., featuring a durable AL29 4C super ferritic stainless steel flue designed for extreme resistance to chloride ion pitting, crevice corrosion, stress corrosion cracking, and corrosion in moderately reducing environments. FCS Corr Guard incorporates an integral joint sleeve for easy joint alignment and aids in shingle condensate across the joint, preventing excessive joint
Corr/Guard® is tested and listed to UL 1738 for positive pressures up to 15" w.g., featuring a durable AL29-4C super ferritic stainless steel flue designed for extreme resistance to chloride ion pitting, crevice corrosion, stress corrosion cracking, and corrosion in moderately reducing environments. FCS Corr/Guard® incorporates an integral joint sleeve for easy joint alignment and aids in shingle condensate across the joint, preventing excessive joint corrosion and leakage. FCS products are manufactured with continuous laser-welded seams and casings, improving durability and reliability and increased efficiency.
Single and Double-Wall Positive Pressure Special Gas Vent engineered for venting today’s high-efficiency natural gas-burning or propane-fired appliances, categories II, III, and IV as defined by the Standard for Gas-Fired Central Furnaces, ANSI Z21.47 and NFPA 54.
What's Included
- 6" to 14" Aluminum Eccentric Increaser
Design Considerations
When venting gas appliances always consult the appliance installation instructions. Horizontal runs, elbows, offsets, vertical height, may be limited by appliance performance specifications.
Horizontal runs must slope a minimum of ¼": 12" (6mm-305mm). Neutral or negative pressure systems must slope upward – away from the appliance. The positive pressure within the vent may slope upward or downward. Provide condensate drainage where required.
Vertical runs are directional-specific and must be properly supported. Supports are required above every offset to prevent vertical loading on elbows.
Corrossion Resistance
Corr/Guard products are designed for use on today’s highly efficient condensing appliances. UNS S44735 (i.e. AL29-4C), a Superferritic Stainless Steel was the first steel to successfully exceed the requirements of UL 1738, “Standard For Venting Systems For Gas-Burning Appliances, Categories II, III, and IV." It is considered the benchmark for condensing flue materials.
Specifications
| Application | ||||||||||
Click to see Appliance Vent Categories
|
||||||||||
| Listing Standard | ||||||||||
| Flue Material | ||||||||||
| Casing Material |
||||||||||
| Max Operating Temperature | 550º F (288 C) | |||||||||
| Max Operating Pressure | 15" w.g. | |||||||||
| Clearance to Combustibles ENCLOSED – VERTICAL @550ºF (288 C) | 1" | |||||||||
| Clearance to Combustibles UNENCLOSED HORIZONTAL or VERTICAL @ 550º F (288 C) | 1" | |||||||||
| Joint Connection | Sleeved – P077 Sealant Required | |||||||||
| Insulation | Ceramic Insulation | |||||||||
| Diameter | 6" to 14" | |||||||||
Warranty
The Metal-Fab 3, 4, and 5-inch diameter Corr/Guard® factory-built gas vent system, when installed according to manufacturer's instructions, as prescribed by Underwriters Laboratories Standard 1738, and when properly and regularly cleaned and maintained as set forth below, are warranted by Metal-Fab Inc. under normal residential use against defects in material or workmanship of the product for parts only for as long as the original consumer owns the gas vent system. During the first ten years of the warranty, Metal-Fab will provide replacement gas vent lengths at no charge. During the balance of the warranty, Metal-Fab will provide replacement gas vent lengths at 50% of the current retail price in effect at the time of the warranty claim.
The defective part(s) must be returned with all transportation charges prepaid by the owner to the Customer Service Department, Metal-Fab Inc., 3025 May Avenue, Wichita, Kansas 67213. Metal-Fab Inc. will in turn ship the repaired or replacement part to the owner, freight collect, with the owner to be responsible for all freight charges. This warranty does not cover any labor or other service charges incurred by the owner, or any parts not manufactured by Metal-Fab Inc.
Click to see Complete Warranty Details
It is the OWNER'S RESPONSIBILITY to establish:
- 1. The date of the original installation of the product;
- 2. The name of the original purchaser;
- 3. The name of the installer;
- 4. That the product was installed according to manufacturer's instructions;
- 5. That the product was properly inspected, cleaned, and serviced once each year by a licensed professional.
Disclaimers and Exclusions
The following shall be applicable to those products of Metal-Fab Inc. described above:
- 1. The warranty described hereinabove shall be IN LIEU of any other warranty, express or implied. Except as set out hereinabove, there are NO other warranties and any statutory or implied warranty of MERCHANTABILITY or fitness for a particular purpose is EXCLUDED from this transaction and shall not apply.
- 2. The sole and exclusive remedy against Metal-Fab Inc. shall be for the repair or replacement of defective parts as provided hereinabove. NO OTHER REMEDY (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. The sole purpose of the stipulated exclusive remedy provided for herein shall be the repair and replacement of defective parts in the manner provided hereinabove. This exclusive remedy shall not be deemed to have failed of its essential purpose so long as Metal-Fab Inc. is willing and able to repair or replace defective parts in the prescribed manner.
-
3. The owner shall not be required to deliver a defective part to Metal-Fab Inc. if:
- (a) The part was destroyed as a result of its defect or any defect in any part covered in this warranty; and
- (b) Metal-Fab Inc. is reasonably satisfied that the part was defective at the time of sale.
- 4. The owner acknowledges that no oral statements purporting to be warranties, representations, or guarantees of any kind about any product of Metal-Fab Inc. have been made to the owner by Metal-Fab Inc., by the original purchaser if different from the owner, or by its dealer which in any way expands, alters, or modifies the terms of the warranty set out herein. Any such statements do not constitute warranties, shall not be relied on by the owner, and are not part of the contract of sale. This writing constitutes a complete and exclusive statement of the terms of any warranty, express or implied, of Metal-Fab Inc.
- 5. There is NO WARRANTY for any defective part of a Metal-Fab product which has been removed from its original installation site or which, in the judgment of Metal-Fab Inc., arises from misuse, mishandling, neglect, flood, lightning, corrosive atmosphere, improper installation of the product, improper servicing of the product, unauthorized modification of the product, improper fuel supply to the product, or the failure of the installer to properly install or service the product as is set out in the installation instructions.
- 6. Some states do not allow the exclusion or limitation of consequential, incidental, or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Documents & Files
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy